Introduction: Twin shaft shredder output size comes from blade thickness and the way material tears, not from a fixed millimeter figure printed on a specification sheet.
Many people treat shredder output as a fixed number written somewhere on a spec sheet, as though a machine could produce a single granule size and only the number changes between models. A screenless twin shaft shredder does not work that way. Output starts forming when the tearing action begins, blade thickness decides where the material splits first, and the material itself bends what happens next. Getting that order right — geometry first, material behavior second — explains why two machines can run the same waste and still deliver different results, why screenless discharge stays coarse, and why secondary granulation usually sits further down the line. It is also the cleanest way to separate a coarse strip from a uniform granulator particle.
How Blade Thickness Shapes Strip Width Before Material Tears
A twin shaft shredder runs two counter-rotating shafts, each carrying a stack of blades separated by spacers, with the two stacks offset so every blade on one shaft bites into the gap on the other. Material dragged between the rotors is sheared, torn, and pushed out through the gaps between blades. Those gaps are the only openings available, so strip width is set geometrically before the first cut happens. SOYU customizes blade thickness to the target strip width, which makes thickness a rotor-mounted parameter rather than a screen swapped in after the fact.
1. Thickness Sets the Nominal Strip Width Before Material Tears
The outer edge of a single blade tears a kerf through the material that matches that blade's thickness, and the spacer sitting against it decides where the next kerf begins. Material comes away as a strip whose main width is the distance between those two kerfs, which follows from blade thickness plus spacer width. That figure is nominal, fixed before anything moves. A thicker blade opens fewer kerfs and produces a wider strip; a thinner blade produces a narrower one. Strip width is therefore a designed parameter inside the cutting chamber, not something that appears only when blades are sharpened or replaced.
2. Material Hardness and Feed Shape Still Bend the Final Strip
After the nominal width, material behavior takes over. A brittle item cracks at the shear point and breaks away cleanly, so the strip lands close to the set width. A tough item — rubber, film, fiber, baled strapping — stretches across the blade, resists, then tears at a point the edge never reached, which leaves a wider and irregular shape. Feed form matters too: hollow containers flatten before they are cut, drums roll and fold, and long pieces bunch up and pass through as a bundle. Hardness, feed shape, blade setup, and discharge conditions all shift the final result.
Why a Screenless Chamber Leaves Coarse Output Uneven
A screenless shredder has nothing underneath the chamber holding material back. In a screened arrangement, oversized pieces are swept back over the cutting zone until they are small enough to fall through the openings, which is how a screen imposes a ceiling on particle size. A screenless design releases material the moment the blades pull it down, so a block can be sliced once and drop out whole. That produces a wide spread: fines, thick slabs, strips with ragged edges, and partially opened pieces, all leaving through the same outlet. For high-tensile and tacky materials such as film, tire sidewalls, and pulper rope, the wide spread is the point. There is no screen to blind, no material recirculating against a mesh, and no energy spent re-cutting wet or fibrous waste that will never pass a small opening anyway. RDF preparation treats fuel as a graded specification rather than one number, and reference frameworks such as EN 15359 describe fuel quality that way, because coarse shredding and fine sizing are separate stages with separate jobs. A screenless twin shaft shredder delivers coarse output on purpose, and that output is not a uniform particle.
Where Secondary Granulation Fits After Twin Shaft Shredding
A granulator or hammer mill works the opposite way: blades or hammers run against a screen, material stays inside until it is small enough to pass, and the screen narrows the particle range into something close to uniform. Feed that machine with twin shaft output and the coarse strips become its raw material. This is where the strip width from the first stage stops being an abstract number and becomes a real load — strips that are too wide for the granulator's inlet slow the feed, take longer to cut, and raise energy per ton. In common recycling-line practice, plants place a screenless twin shaft shredder as the primary unit and a granulator downstream, then tune blade thickness to what the second machine can comfortably accept. Plastic recycling guidance treats size reduction as a chain of pre-treatment steps rather than a single operation, since no one stage both reduces volume and delivers a narrow particle range. Thinner blades give the granulator an easier feed, while thicker blades keep grip on bulky hollow items and protect throughput in the first stage. Blade thickness is the handoff between coarse tearing and fine granulation, which is why it deserves to be chosen with both ends of the line in view.
Conclusion
Output size in screenless twin shaft shredding is a designed starting point, not a catalog value. Blade thickness sets the nominal strip width in the cutting chamber, and hardness, feed shape, and blade setup decide how closely the real strip follows that geometry. The missing screen is why the discharge stays coarse and ranges widely, and that same open chamber is what keeps tough and tacky material moving. When a line needs uniform particles, a secondary granulator with its own screen does that work. Anyone comparing machines can now read a thickness figure for what it is: the first decision in a two-stage sizing chain.
FAQ
Q: How does blade thickness affect output size in a twin shaft shredder?
A: Blade thickness sets the gap between cutting edges on the rotor stack, so it fixes the nominal width of the strips that come away when material is torn. Thicker blades produce wider strips and thinner blades produce narrower ones. The final piece still varies with hardness, feed shape, and blade setup, so thickness is best read as the design starting point rather than an exact output figure.
Q: Does a screenless twin shaft shredder produce uniform particles?
A: No. With no screen under the chamber, material leaves as soon as the blades pull it down, so output ranges from fines and slabs to ragged strips and partly opened pieces. That coarse, uneven discharge is deliberate, because it keeps tough and tacky waste moving without blinding a mesh. Uniform particles come from a later stage, not from the twin shaft unit itself.
Q: Can a secondary granulator make twin shaft shredder output more uniform?
A: Yes. A granulator holds material against a screen and keeps cutting until pieces pass through the openings, which narrows the particle range considerably. The twin shaft strips become its feed, and strip width affects how hard that machine works. Matching blade thickness to the granulator's inlet and capacity gives a smoother second stage and more consistent final particles.
Sources / References
European, American and International Standards online - iTeh Standards
Design Guide Welcome Page - Association of Plastic Recyclers (APR)


